| Issue |
Title |
File |
| Vol 21, No 2 (2020) |
Effect of fixing the pass-through turning tool in the tool holder on the roughness and surface macro deviations during turning |
(Rus)
|
|
Allenov D.G., Deinova K.B., Solomatin S.V., Lazarenko O.I.
|
| Vol 21, No 3 (2020) |
Less wear on the piston skirts of internal combustion engines |
(Rus)
|
|
Asoyan A.R., Gorshkov A.S., Israelyan A.H.
|
| Vol 19, No 1 (2018) |
On hydraulic analysis of the main parameters of longitudinalcirculating flow |
(Rus)
|
|
Ponomarev N.K., Schesnyak L.E.
|
| Vol 19, No 2 (2018) |
DETERMINATION OF CONTACT STRESSES AND GAPS IN CHAIN TRANSMISSION HINGES |
(Rus)
|
|
Belousov Y.V., Strashnov S.V.
|
| Vol 19, No 2 (2018) |
COMPUTER-AIDED DESIGN OF TYPE C4: COMPRESSOR BLADE PROFILE |
(Rus)
|
|
Vinogradov L.V., Mamaev V.K., Oshcepkov P.P.
|
| Vol 19, No 2 (2018) |
INFLUENCE OF ENERGY ON PHASE COMPOSITION OF END-PRODUCT OBTAINED BY VACUUM-FREE ELECTRIC ARC SYNTHESIS OF CUBIC SILICON CARBIDE |
(Rus)
|
|
Pak A.Y., Mamontov G.Y., Bolotnikova O.A.
|
| Vol 19, No 3 (2018) |
Heat pump coefficient of conversion and power on off-nominal modes |
(Rus)
|
|
Antipov Y.A., Shatalov I.K., Shatalova I.I., Shkarin K.V.
|
| Vol 19, No 3 (2018) |
Application of computer processing of experimental data from analysis of chip formation zone on photoelastic models |
(Rus)
|
|
Zhed O.V., Kopylov V.V.
|
| Vol 19, No 4 (2018) |
Large-sized transformable space antenna reflector made оf composite materials dynamic modeling process |
(Rus)
|
|
Reznik S.V., Chubanov D.E.
|
| Vol 19, No 4 (2018) |
Reserves for improving the design of shafts |
(Rus)
|
|
Kirilovskiy V.V.
|
| Vol 19, No 1 (2018) |
Calculation of clamping error when mounting a workpiece on fixture supports |
(Rus)
|
|
Belousov Y.V.
|
| Vol 19, No 1 (2018) |
Technique for conducting experimental studies on stress-strain state of P-3 profile interference fits |
(Rus)
|
|
Rozhkova E.A., Chetverikov S.V.
|
| Vol 18, No 1 (2017) |
OSCILLATIONS MULTILAYERED COMPOSITE RODS FROM MATERIALS IN THE FIELD OF CENTRIFUGAL FORCES |
(Rus)
|
|
Nurimbetov A.U., Dudchenko A.A.
|
| Vol 18, No 1 (2017) |
ANALYSIS CONDITIONS FOR RELIABLE ATTACH OF WORKPIECES DURING LATHE MACHINING ON THE MASHINES WITH NUMERICAL SOFT-WARE CONTROL |
(Rus)
|
|
Belousov Y.V.
|
| Vol 18, No 2 (2017) |
COMPARISON OF EFFICIENCY PETROL OF ENGINE WITH STRAUTIFIED CHARGE AND AUTOMOTIVE DIESEL |
(Rus)
|
|
Vallejo Maldonado P.R., Antipov Y.A., Oshchepkov P.P.
|
| 1 - 15 of 15 Items |
|
