Vol 15, No 2 (2019)

Analysis and design of building structures

Determining the width of the workpiece under bending conditions with stretching of the stamped part

Morozov Y.A., Verkhov E.Y.

Abstract

Aims of research. This paper deals with the problem of determining the radius of the neutral surface of the bending strip at the same time the action of tensile stresses. Methods. In the development of technological processes of sheet bending and the calculation of the initial billet (sweep), most often considered a flat stress state and preference is given to the theory of pure bending, providing uniform curvature of the individual layers of metal under the action of the bending moment and neglecting the action of transverse tensile forces. However, in reality, bending is always accompanied by sliding of the metal along the deforming tool, causing the appearance of friction forces and creating a complex loading in the form of plastic bending with stretching in the metal, which will additionally displace the neutral surface, forcing the experienced one to adjust the technology of manufacturing bent parts. Provides an overview and analysis of the most famous works dedicated to the topic, specifying the distribution of the contact stresses from the inner surface to the center of curvature and developed the theory of complex bending, which allows to specify the radius of the neutral surface in conditions of stretching of the flexible strip of the additional tangential stresses. Results. The results obtained will allow to simulate the stress state of the metal in the development of technological processes of sheet stamping and, in particular, to assess the specific braking force during the bending (straightening) of the strip in the process of pulling through the thresholds and brake edges of the die tooling to eliminate possible defects in the elongated parts and to clarify the dimensions of the workpiece and the finished profile.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):83-89
pages 83-89 views

Determination of parameters of plastic deformation of elliptic membranes

Galimov N.K., Yakupov S.N.

Abstract

Introduction. Thin-walled structural elements, combining lightness with high strength, are widely used in all industries. Widespread round design elements. However, based on the functional purpose, thin-walled structural elements of various shapes in plan are becoming more and more common. Methods. A technique has been developed for the study of thin elliptic membranes for the case of plastic deformation under the action of uniform pressure. The deflections of the membranes in the experiment are more than ten thicknesses. In this regard, to solve the problem, the following are used: geometric nonlinear relations for the deformations of the middle surface (according to Kh.M. Mushtari and K. Z. Galimov), relations for finite displacements and deformations for curvature expressions (according to K.Z. Galimov), physical relations (according to the theory of plasticity A.A. Ilyushin). Due to the smallness of the membrane thickness, only tensile membrane strains and forces are taken into account. The problem is solved by the Bubnov - Galerkin method and reduced to solving a nonlinear system of three algebraic equations. The “shooting” algorithm for solving the resulting system of equations is described. Results. The work on the assessment of the reliability of the results. To estimate the error, the comparison of the calculation results with the experimental results of G.D. Golovlev was also performed. An example of the calculation of an elliptical membrane is considered.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):90-95
pages 90-95 views

Development of the design module of the software and hardware complex to ensure the safety of mutually influencing HPS

Rubin O.D., Antonov A.S., Bellendir E.N., Kobochkina E.M., Kotlov O.N.

Abstract

Relevance. As part of the implementation of the Federal Law No. 117-FZ “On the Safety of Hydraulic Structures”, it is necessary to continuously monitor the state of hydraulic structures and related facilities by equipping with control and measuring instruments. The development of modern computer complexes allows us to carry out and predict the state of objects by combining computational research and field observations. The work is aimed at organizing a comprehensive assessment of the state of the HPS and ensuring the safety of existing and projected mutually influential complexes. Aims of research. Improving the safety of the operated (under construction) complex of interfering hydraulic structures. Assessment of sufficient and highquality engineering and repair work carried out on the HPS. Development of recommendations for improving the efficiency of construction of new and modernization of operated hydropower facilities. HPS on the example of the Zagorsk HPS. Methods. Representation of the interaction ideology of various software systems of mathematical modeling, using control and measuring instruments data for calibration and verification of mathematical models. Results. The structure of the HSC calculation module was updated, systematization of the calculation models was carried out, interaction and transfer of the initial data to the calculation module of the software and hardware complex was revealed. The implementation of scientific research is aimed at improving the safety of the complex hydraulic structures.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):96-105
pages 96-105 views

Geometrical investigations of middle surfaces of shells

Formation surfaces of Monge by the kinematic method in AutoCAD environment

Romanova V.A.

Abstract

Aims of research. Studying the possibility of forming Monge carved surfaces, defined by the method of their formation, creating an algorithm and program in the AutoLISP language to demonstrate the formation of surfaces in the AutoCAD environment in a dynamic mode. Methods. Monge carved surfaces are formed by a flat curve, located in the tangent plane to the fixed guide of the developable surface, when the plane and the curve roll along the guide surface without sliding. The described method of formation of these surfaces allows to perform their formation by the kinematic method in the AutoCAD environment using AutoLISP software. The article describes the construction of the Monge surfaces using cylindrical and conical surfaces as guides. A straight line and a sine wave are used as the forming lines. Results. An algorithm and a program in the AutoLISP language were created to form sets of compartments of several Monge surfaces and to visualize the formation of these surfaces in a dynamic mode by sequentially displaying the compartments on the monitor screen. The mini-film about formation of Monge surface by rolling a plane with a straight line along a circular cone is created. In the mini-film the drawings received by transformation of drawings of the AutoCAD environment are used.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):106-116
pages 106-116 views

Numerical methods of structures’ analysis

Numerical analysis of the stress-strain state of thin shells based on a joint triangular finite element

Klochkov Y.V., Nikolaev A.P., Vakhnina O.V.

Abstract

Relevance. The use of the finite element method for determining the stressstrain state of thin-walled elements of engineering structures predetermines their discretization into separate finite elements. Splitting irregular parts of the structure is impossible without the use of triangular areas. The triangular elements of shell structures are joint in displacements and in their derivatives only at the nodal points. Therefore, ways to improve the compatibility conditions at the boundaries of triangular elements are relevant. Aims of research. The aim of the work is to improve the compatibility conditions at the boundaries of adjacent triangular elements based on equating the derivatives of normal displacements in the middle of the boundary sides. Methods. In order to improve the compatibility conditions at the boundaries of triangular elements in this work, the Lagrange functional is used with the condition of ensuring equality in the middle of the sides of adjacent elements derived from normal displacements in the directions of perpendiculars tangent to the middle surface of the shell. Results. Using the example of analysing an elliptical shell, the efficiency of using a joint triangular finite element is shown, whose stiffness matrix is formed in accordance with the algorithm outlined in this article.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):117-126
pages 117-126 views

Numerical analysis of layered composite panel behavior with interlaminar defects subject to dynamic loads

Medvedskiy A.L., Martirosov M.I., Khomchenko A.V.

Abstract

Aims of research. Polymer unidirectional composite laminate panel behavior with interlaminate defects under action of different dynamic loads is consider. Methods. Normal modes and eigenvalues of rectangular composite panels in the presence multiple delamination different sizes ellipsoidal form are calculated. The dependences of the maximum deflections from the frequency of the stationary pressure field action are constructed. Distribution field of panels plies failure index under action of nonstationary pressure field by using different failure criteria for composites is determined. Results. Modeling methodology composite panels behavior in the presence multiple interlaminar defects under action of different dynamic loads is developed. Analysis of failure panel with the use of different failure criteria for composites is carried out.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):127-134
pages 127-134 views

Theory of elasticity

Extraction of consistent shell theory equations from 3D theory of elasticity

Zveryaev E.M.

Abstract

Aims of research. Derivation of consistent equations of the theory of thin elastic shells without hypotheses and stress averaging over the shell thickness. Methods. Using the iterative method of Saint-Venant - Picard - Banach, the three-dimensional problem of the theory of elasticity is solved without any hypotheses. By the principle of compressed mappings, the solution converges asymptotically, regardless of the choice of the values of the initial approximation. Results. A method has been developed for integrating the spatial equations of the theory of elasticity in curvilinear coordinates for a thin shell. The presence of a small parameter allows the integration of the system of equations in such a way that the output data of the first operator is input to the next operator, etc., dividing the original complex operator into a sequence of simple integrable Picard type operators. Each equation contains terms of only one asymptotic order.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):135-148
pages 135-148 views

Unloading wave in the cylindrical network from nonlinear elastic fibers

Rustamova M.A.

Abstract

Aims of research. Investigation of a wave of unloading in a cylindrical network of nonlinear elastic fibers. Given the many options for wave propagation in cylindrical networks, an attempt is made to solve the problem of continuous waves. Methods. The movement of the network in the axial direction is cornsidered. nonlinear elastic fibers; To a basis of a cylindrical system are accepted: an individual vector i r parallel wave of unloading; cylindrical network; to a cylinder axis, j r · an individual vector of a tangent to cross-section section continuous waves of the cylinder, k · an individual vector perpendicular to the previous ones, x - is the coordinate in the direction of the axis of the cylinder, y - is the length of an arc of the circumference of the cylinder. The problem reduces to a hyperbolic system of equations under appropriate conditions. Since the wave speed increases when the net is stretched, the stretch wave will obviously be discontinuous. In order to study continuous waves, the problem of wave propagation is solved when unloading a pre-stretched cylinder from a nonlinear basis. The problem is solved by the method of characteristics. Results. The results are illustrated with calculations and can be used at calculations of various flexible pipes, including flexible drilling.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):149-157
pages 149-157 views

Dynamics of structures and buildings

Static and dynamic analyses of the heightening of concrete face gravel dam Limon (Peru)

Lyapichev Y.P.

Abstract

Aims of research. Expert validation of all proposed design solutions, development of necessary design solutions for the heightening of the Limon dam according to the ICOLD recommendations. Methods. The detailed static and seismic (dynamic) analyses of stressstrain state and seepage of concrete face rockfill dam Limon (Peru) were performed using the advanced software FLAC-3D (USA) and PLAXIS 2D (Holland), respectively. The elasto-plastic model with Mohr - Coulomb criterion with variable shear angles of gravel and pebble zones of dam materials and its foundation soils was used in the static and seismic (dynamic) analyses of the dam. The dynamic nonlinear analyses of stress-strain state of two variants of Limon dam with full reservoir under Maximum Credible Earthquake (MCE) action of the Mar-Chile Earthquake accelerogram. Results. On the base of these analyses the recommendations were developed for the project of the dam heightening from 43 up to 82 m before the initial filling of the reservoir. Expert validation of all proposed design solutions, necessary design solutions for the heightening of the Limon dam were developed according to the ICOLD recommendations.

Structural Mechanics of Engineering Constructions and Buildings. 2019;15(2):158-168
pages 158-168 views

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies